Cambridge Audio 540D Bedienungsanleitung PDF herunterladen (Seite 5)

RGB/SCART

Use a SCART/Peritel cable to connect to the 21-pin scart input jack of a

TV. SCART carries both audio (stereo) and video (as either Composite,

S-Video or RGB) at the same time.

Analog Video Outputs

Composite — Connect to your television via 75 ohm RCA/phono cable

designed specifically for video use.

S-Video — Connect to your television via dedicated S-Video cable.

Component — Connect to the YCbCr or YPbPr terminals of a television

set via three 75 ohm RCA/phono cables designed specifically for video

use.

HDMI Out

HDMI (High-Definition Multi-Media Interface) is a purely digital

connection that can carry both audio and video. Use a dedicated HDMI

cable to connect to a TV/monitor with a compatible HDMI input.

540D V2azur

Rear panel connections

ENGLISH

AC power socket

Once you have made all audio and video connections, plug the IEC type

AC power cable into the rear of the unit and an appropriate mains

socket, and then switch on. Your DVD player is now ready for use.

Power On/Off

Switches the unit on and off.

Control Bus

In — Allows un-modulated commands from multi-room systems or other

components to be received by the unit.

Out — Loop out for Control Bus commands to another unit.

IR (Infra-Red) Emitter In

Allows modulated IR commands from multi-room systems or IR repeater

systems to be received by the unit. Commands received here are not

looped out of the Control Bus. Refer to the Custom Installation section

of this manual for more information.

Digital Outputs

Digital audio outputs are normally used to connect to a suitable Audio/

Video Receiver for surround sound decoding (output must be set for

‘RAW Bitstream’ — refer to the Audio Setup section). These outputs can

also be used to connect to a separate DAC or digital recording device

(output must be set for ‘PCM Stereo’ — see Audio Setup section).

Toslink Optical — Use a high quality TOSLINK fibre optic cable.

S/P DIF Co-axial Digital — Use a high quality 75 ohm digital RCA/Phono

interconnect cable designed specifically for digital audio use.

5.1 Channel Audio Out

If Downmix is set to ‘Off’ in the Speaker Setup section of the 540D V2’s

Setup menus, these sockets provide 5.1 output from the 540D V2's

built-in Dolby Digital/Pro Logic II decoder. This can be used to connect

to the 5.1 audio line-level inputs of an amplifier/AV receiver or amplified

speaker package if required.

If Downmix is set to ‘On’, the Left and Right outputs only are active and

provide a stereo downmixed output.

Stereo Audio Out

A separate permanent Stereo output (or Stereo downmix in the case of

multi-channel material) is available for connection to the analog stereo

inputs of an amplifier/AV receiver, etc. This is the best connection to use

for listening to CDs.

Note: The preferred connection method for video sources is always

HDMI (highest quality, and can also carry audio in some

circumstances), then Component Video, RGB/SCART, S-Video, and

Composite Video (lowest quality). The HDMI and Component

outputs also support Progressive Scan which gives better picture

quality if supported by your TV.

Important Note

This unit has been designed to play video DVDs,

compact discs, recordable CDs (CD-R) and

rewritable CDs (CD-RW) bearing the identification

logos shown here. No other discs can be used. The

CD-R/CD-RW discs should contain properly recorded

TOC (Table of Contents) information so that they can

be played back. This unit can play only the discs

recorded in the CD-DA format designed for music

reproduction. Do not attempt to play a disc on this unit containing

other data, such as a CD-ROM for PCs.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Cambridge Audio 540D Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für DVD Spieler Cambridge Audio 540D